Board logo

標題: 想了解一下自己電腦的配置 [打印本頁]

作者: kelvinyoyo    時間: 2009-7-28 01:58 PM     標題: 想了解一下自己電腦的配置

小弟既電腦在5-6年前買...相信大部份配置都不夠用嫁啦...所以想換底板 或者甚至連埋其他介面卡,但自己又唔係好識呢方面d資料,唔知點樣選擇一d可以岩返部電腦其他配置既底板及介面卡...所以希望師兄比d意見..首先我想了解一下自己部電腦既配置

以下係o係執行度輸入dxdiag 得出的report的一部份 (配置真的很低..請不要笑-_-")


------------------
System Information
------------------
Time of this report: 7/28/2009, 11:45:08
       Machine name: YUNG-UJO7F3XL80
   Operating System: Windows 2000 Professional (5.0, Build 2195)
           Language: Chinese (Regional Setting: Chinese)
System Manufacturer: WINSONIC
       System Model: WSP4M800-L
               BIOS: Default System BIOS
          Processor: Unknown Intel              Memory: 224MB RAM
          Page File: 271MB used, 423MB available
        Windows Dir: C:\WINNT
    DirectX Version: DirectX 9.0c (4.09.0000.0904)
DX Setup Parameters: Not found
     DxDiag Version: 5.03.0001.0904 32bit Unicode
------------
DxDiag Notes
------------
  DirectX Files Tab: No problems found.
      Display Tab 1: The file vtdisp.dll is not digitally signed, which means that it has not been tested by Microsoft's Windows Hardware Quality Labs (WHQL).  You may be able to get a WHQL logo'd driver from the hardware manufacturer. Direct3D 7 test results: All tests were successful. Direct3D 8 test results: Failure at step 32 (User verification of Direct3D rendering): HRESULT = 0x00000000 (error code) Direct3D 9 test results: All tests were successful.
        Sound Tab 1: No problems found.
          Music Tab: No problems found.
          Input Tab: No problems found.
        Network Tab: No problems found.
--------------------
DirectX Debug Levels
--------------------
Direct3D:    0/4 (n/a)
DirectDraw:  0/4 (retail)
DirectInput: 0/5 (n/a)
DirectMusic: 0/5 (n/a)
DirectPlay:  0/9 (retail)
DirectSound: 0/5 (retail)
DirectShow:  0/6 (retail)
---------------
Display Devices
---------------
        Card name: VIA/S3G UniChrome Pro IGP
     Manufacturer: VIA/S3G
        Chip type: VIA/S3G UniChrome Pro IGP
         DAC type: Internal
       Device Key: Enum\PCI\VEN_1106&DEV_3344&SUBSYS_11223344&REV_01
   Display Memory: 32.0 MB
     Current Mode: 1024 x 768 (32 bit) (60Hz)
          Monitor:   Monitor Max Res: 1600,1200
      Driver Name: vtdisp.dll
   Driver Version: 6.14.0010.0275 (English)
      DDI Version: 9 (or higher)
Driver Attributes: Final Retail
Driver Date/Size: 12/27/2005 11:06:14, 3490432 bytes
      WHQL Logo'd: No
  WHQL Date Stamp: None
              VDD:          Mini VDD: vtmini.sys
    Mini VDD Date: 12/27/2005 11:06:22, 247040 bytes
Device Identifier: {D7B71FE6-7004-11CF-E751-2831A0C2CB35}
        Vendor ID: 0x1106
        Device ID: 0x3344
        SubSys ID: 0x11223344
      Revision ID: 0x0001
      Revision ID: 0x0001
      Video Accel: ModeMPEG2_A ModeMPEG2_B ModeMPEG2_C ModeMPEG2_D
Deinterlace Caps: n/a
         Registry: OK
     DDraw Status: Enabled
       D3D Status: Enabled
       AGP Status: Enabled
DDraw Test Result: Not run
D3D7 Test Result: All tests were successful.
D3D8 Test Result: Failure at step 32 (User verification of Direct3D rendering): HRESULT = 0x00000000 (error code)
D3D9 Test Result: All tests were successful.


關於呢樣野..小弟有d野想問:請問小弟部電腦既cpu係版本幾多?(例如pentium幾等等)
display卡係唔係連埋o係個底板度內罝?
ram係唔係ddr ? ram依家有幾多版本...?好似見有ddr -ddr 4都有... 另外係唔係有32mb既ram分左去內罝display度?


因為小弟主要都係想用電腦黎打機.(-.-")但依家既配置除左2d game之外,3d online game真的大部份都不能順暢運行(即使只單開)
聽人講要game行得好,display比較重要,所以小弟有以下幾個方案:

1)想換display卡(大d mb數),之後先再加ddr 既ram,其他保留,但係唔係因為依家係底板內罝display,所以要換埋底板先可以外罝到高mb數既display?如果唔係有冇方法o係現在底板上,配上高mb數既display?

2)成個底板換...換做ddr2 ram 同埋 外罝display既底板...但又好似因為驚cup太舊而要連cpu換埋

以上2個方案...邊個可行d?其實小弟想大約有5xx mb display,1gb/2gb既 ram...因此只係識呢2樣,cpu唔係識得好詳細所以唔知要咩要求...希望大家可以比d意見
作者: tommy814    時間: 2009-8-2 04:34 PM

成部機換!~
作者: goku888    時間: 2009-8-2 10:15 PM

成部機換!~
tommy814 發表於 2009-8-2 04:34 PM
哈哈。。簡而精,一矢中的




歡迎光臨 公仔箱論壇 (http://5.39.217.77/) Powered by Discuz! 7.0.0